wideband amplifier rfc1g22-24 k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 1 / 5 version 5.9 product features applications ? gaas mmic ? very low distortion ? guaranteed broadband power gain ? heat sink 99.9% copper, ag or gold plate ? excellent thermal conductivity ? single supply voltage @ 24v ? low dc power consuption ? no external circuit needed ? drive amplifier description the rfc1g22- 24 is specifically designed for up to 1ghz in frequency as amplifiers. this hybrid dynamic range amplifier module operates with a single voltage supply of 24v(dc). the rfc1g22- 24 is equipped with over-voltage suppressor. electrical specifications @ v dd = 24v, t a = 25c parameter unit min typ max condition operating frequency mhz 20 - 1000 - gain db 21.0 22.0 - f = 1000mhz gain flatness db - 1.5 2.0 f = 20 ~ 1000mhz input / output vswr - 2.5 : 1 2.0 : 1 - - power output 1db comp. dbm 29.0 30.0 - f = 20 ~ 1000mhz imd3 dbc 56.0 60.0 - total pout = 23dbm. tone spacing 1mhz noise figure db - 4.0 7.0 f = 20 ~ 1000mhz supply current ma - 400 430 - absolute maximum ratings parameter unit min typ max condition v dd / v rfout vdc - - 28 - rf out dbm - - 15 single tone storage temperature c -40 - 100 - operating temperature c -20 - 100 - package type : dp-27
wideband amplifier rfc1g22-24 k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 2 / 5 version 5.9 typical performance @ 25c parameter unit typ frequency mhz 20 500 1000 gain db 21 22 22 input return loss db -14 -30 -15 output return loss db -16 -16 -17 power output 1db comp dbm 29 30 29 oip3 dbm 48.5 51 49 noise figure db 3.6 3.5 4.8 supply voltage v 24 current ma 430 (max) s-parameters power output 1db compression -70 -60 -50 -40 -30 -20 -10 0 10 20 30 200 400 600 800 1000 1200 1400 1600 1800 2000 frequency(mhz) magnitude(db) 20 s21 s11 s22 noise figure oip 3 0 1 2 3 4 5 6 20 100 200 300 400 500 600 700 800 900 1000 frequency(mhz) noise figure(db)
wideband amplifier rfc1g22-24 k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 3 / 5 version 5.9 note for correct use 1. on the power input port (pin#5), 47uf/35v capacitor gnd is recommended. 2. the heat sink of catv hybrids is to be mounted in direct contact with the metal case of the equipment. heat conducting grease should be applied to the module/equipment interface and the unit tightly secured. 3. put the power off before adjusting in/output matching of the system. 4. the unit must have a common ground with the equipment and the analyzer. 5. pay close attention to the input voltage not to over power the hybrid. 6. the space between bottom of socket and the tip of the lead is recommended to have space of 2mm+ to protect the pin. 7. do not open the plastic cover to change the matching inside the hybrid. once opened, rfhic will not be responsible for the hybrid. esd protection gallium arsenide integrated circuits are sensitive to electrostat ic discharge (esd) and can be damaged by static electricity. p roper esd control techniques should be used when handling these devices. some of the precautions recommended are; - person at a workbench should be earthed via a wrist strap and a resistor. - all mains-powered equipment should be connected to the mains via an earth-leakage switch. - equipment cases should be grounded. - relative humidity should be maintained between 40% and 50%. - an ionizer is recommended. keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench.
wideband amplifier rfc1g22-24 k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 4 / 5 version 5.9 package dimensions (type: dp-27) * unit: mm[inch] | tolerance: 0.2[.008] front view side view pin description pin no function pin no function pin no function 1 rf input 4 - 7 gnd 2 gnd 5 vcc 8 gnd 3 gnd 6 - 9 rf output * mounting configuration notes 1. ground / thermal via holes are critical for the proper performance of this device. 2. add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. mounting screws can be added near the part to fasten the board to a heatsink. ensure that the ground / thermal via hole regi on contacts the heatsink. 4. do not put solder mask on the backside of the pcb in the region where the board contacts the heatsink. 5. rf trace width depends upon the pcb material and construction. 6. use 1 oz. copper minimum. top view
wideband amplifier rfc1g22-24 k orean facilities : 82-31-250-5078 / rfsales@rfhic.com all specifications may change without notice u s facility : 919-677-8780 / sales@rfhicusa.com 5 / 5 version 5.9 revision history part number release date version modification data sheet status rfc1g22-24 2012.11.6 5.9 electrical specifications, typical performance modification - rfc1g22-24 2012.9.5 5.8 - - rfhic corporation reserves the right to make changes to any prod ucts herein or to discontinue any product at any time without n otice. while product specifications have been thoroughly examined for reliability, rfhic corporation strongly recommends buy ers to verify that the information they are using is accurat e before ordering. rfhic corporation does not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including wi thout limitation consequential or incidental damages. rfhic products are not intended for use in life support equipment or application where malfunction of the product can be expect ed to result in personal injury or death. buyer uses or sells such products for any such unintended or unauthorized application, buyer shall i ndemnify, protect and hold rfhic corporat ion and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such unauthorized use. sales, inquiries and support should be directed to the local au thorized geographic distributor for rfhic corporation. for custo mers in the us, please contact the us sales team at 919- 677-8780. for all other inquiries, please contact the international sales team at 82-31-250-5078.
|
